View MC10H330_113745.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Quad Bus Driver/Receiver with 2-to-1 Output Multiplexers
The MC10H330 is a Quad Bus Driver/Receiver with two-to-one output multiplexers. These multiplexers have a common select and output enable. When disabled, (OE = high) the bus outputs go to -2.0 V. Their output can be brought to a low state (VOL) by applying a high level to the receiver enable (RE = High). The parameters specified are with 25 loading on the bus drivers and 50 loads on the receivers. * Propagation Delay, 1.5 ns Typical Data-to-Output * Improved Noise Margin 150 mV (Over Operating Voltage and Temperature Range) * Voltage Compensated * MECL 10K-Compatible MAXIMUM RATINGS
Characteristic Power Supply (VCC = 0) Input Voltage (VCC = 0) Output Current -- Continuous -- Surge Operating Temperature Range Storage Temperature Range -- Plastic -- Ceramic Symbol VEE VI Iout TA Tstg Rating -8.0 to 0 0 to VEE 50 100 0 to +75 -55 to +150 -55 to +165 Unit Vdc Vdc mA C C C
MC10H330
L SUFFIX CERAMIC PACKAGE CASE 758-02
P SUFFIX PLASTIC PACKAGE CASE 724-03 FN SUFFIX PLCC CASE 776-02
DIP PIN ASSIGNMENT
VCC XBUS 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 VCC0 YBUS ZBUS OE Y0 Y1 Z0 Z1 RE ZIN YIN VCC0
ELECTRICAL CHARACTERISTICS (VEE = -5.2 V 5%) (See Note)
0 Characteristic Power Supply Current Input Current High Pins 5-8, 17-20 Pins 16, 21 Pin 9 Input Current Low High Output Voltage Low Output Voltage High Input Voltage Low Input Voltage Symbol IE IinH -- -- -- IinL VOH VOL VIH VIL tpd 1.8 0.5 1.0 0.8 0.8 0.5 1.3 tr tf 0.5 0.5 5.3 2.0 3.2 2.2 2.1 2.2 4.0 2.0 2.0 1.8 0.5 1.0 0.8 0.8 0.5 1.3 0.5 0.5 5.3 2.0 3.2 2.2 2.1 2.2 4.0 2.0 2.0 1.8 0.5 1.0 0.8 0.8 0.5 1.3 0.5 0.5 5.3 2.0 3.2 2.2 2.4 2.2 4.0 2.0 2.0 ns ns 0.5 667 514 475 -- -- -- -- 0.5 417 321 297 -- -- -- -- 0.3 417 321 297 -- -0.735 -1.60 -0.735 -1.45 A Vdc Vdc Vdc Vdc Min -- Max 157 Min -- 25 Max 143 Min -- 75 Max 157 Unit mA A
WBUS VCC0 X1 X0 W1 W0 S WIN XIN VEE
-1.02 -0.84 -0.98 -0.81 -0.92 -1.95 -1.63 -1.95 -1.63 -1.95 -1.17 -0.84 -1.13 -0.81 -1.07 -1.95 -1.48 -1.95 -1.48 -1.95
AC PARAMETERS
Propagation Delay Select-to-Input Data-to-Bus Output Select-to-Bus Output OE-to-Bus Output Bus-to-Input RE-to-Input Data-to-Receiver Input Rise Time Fall Time ns
Pin assignment is for Dual-in-Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 6-11 of the Motorola MECL Data Book (DL122/D). NOTE: Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 Ifpm is maintained. Receiver outputs are terminated through a 50-ohm resistor to -2.0 volts dc. Bus outputs are terminated through a 25-ohm resistor to -2.0 volts dc.
3/93
(c) Motorola, Inc. 1996
2-299
REV 5
MC10H330
LOGIC DIAGRAM
OE S
21 9
W0
8
VCC0 VCC VCC0 VCC0 VEE
= = = = =
PIN 24 PIN 1 PIN 13 PIN 4 PIN 12 3 WBUS
W1 WIN X0
7 10 6 2 XBUS
X1 XIN Y0
5 11 20 23 YBUS
Y1 YIN Z0
19 14 18 22 ZBUS
Z1 ZIN RE
17 15 16
MULTIPLEXER TRUTH TABLE
OE H L L S X L H WBus XBus YBus ZBus
RECEIVER TRUTH TABLE
RE H L Win L WBus Xin L XBus Yin L YBus Zin L ZBus
-2.0 V -2.0 V -2.0 V -2.0 V W0 X0 Y0 Z0 W1 X1 Y1 Z1
MOTOROLA
2-300
MECL Data DL122 -- Rev 6
MC10H330
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
B -N- Y BRK U D Z -L- -M- 0.007 (0.180)
M
0.007 (0.180)
M
T L-M
S
N
S S
T L-M
N
S
W
28 1
D
X VIEW D-D
G1
0.010 (0.250)
S
T L-M
S
N
S
V
A Z R C
0.007 (0.180) 0.007 (0.180)
M
T L-M T L-M
S
N N
S
H
0.007 (0.180)
M
T L-M
S
N
S
M
S
S
E 0.004 (0.100) G G1 0.010 (0.250)
S
K1
J
-T- VIEW S
SEATING PLANE
K F VIEW S 0.007 (0.180)
M
T L-M
S
N
S
T L-M
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10_ 0.410 0.430 0.040 ---
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10_ 10.42 10.92 1.02 ---
MECL Data DL122 -- Rev 6
2-301
MOTOROLA
MC10H330
OUTLINE DIMENSIONS
L SUFFIX CERAMIC DIP PACKAGE CASE 758-02 ISSUE A
B
24 13 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL.
L
P
1
12
-A- N C K G F D 24 PL 0.25 (0.010)
M
J
DIM A B C D F G J K L N P
-T-
SEATING PLANE
INCHES MIN MAX 1.240 1.285 0.285 0.305 0.160 0.200 0.015 0.021 0.045 0.062 0.100 BSC 0.008 0.013 0.100 0.165 0.300 0.310 0.020 0.050 0.360 0.400
MILLIMETERS MIN MAX 31.50 32.64 7.24 7.75 4.07 5.08 0.38 0.53 1.14 1.57 2.54 BSC 0.20 0.33 2.54 4.19 7.62 7.87 0.51 1.27 9.14 10.16
TA
M
-A-
24 1 13
-B-
12
P SUFFIX PLASTIC DIP PACKAGE CASE 724-03 ISSUE D
NOTES: 1. CHAMFERED CONTOUR OPTIONAL. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 4. CONTROLLING DIMENSION: INCH. DIM A B C D E F G J K L M N INCHES MIN MAX 1.230 1.265 0.250 0.270 0.145 0.175 0.015 0.020 0.050 BSC 0.040 0.060 0.100 BSC 0.007 0.012 0.110 0.140 0.300 BSC 0_ 15_ 0.020 0.040 MILLIMETERS MIN MAX 31.25 32.13 6.35 6.85 3.69 4.44 0.38 0.51 1.27 BSC 1.02 1.52 2.54 BSC 0.18 0.30 2.80 3.55 7.62 BSC 0_ 15_ 0.51 1.01
C -T-
SEATING PLANE
L
K E G F D
24 PL
NOTE 1
N J
24 PL
M
0.25 (0.010)
M
M
TB
M
0.25 (0.010)
TA
M
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-302
*MC10H330/D*
MC10H330/D MECL Data DL122 -- Rev 6

▲Up To Search▲

Price & Availability of MC10H330

	To Download MC10H330 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .